Shutter Repair in Cumberland by Cumberland Window Treatments

A folding set won't close no matter what you try

The panel binds every August and closes fine in winter

The tilt rod has come away from a louver

A louver spins loose in its hole and won't stay

One louver cracked and the rest are fine

A shutter has dropped at the latch edge

A panel no longer sits flat against the frame

Hinge screws keep backing out of the same panel

Magnets no longer hold the panels closed

A gap has opened at a top corner of the frame

Manufacturer, material and finish identified from the panel and the frame before any parts conversation starts

Match confirmed in writing before the visit is scheduled, since an unmatchable panel changes the whole plan

Louver size, frame profile and tilt style recorded, because those three decide whether a replacement panel can exist at all

Existing color compared against the current factory range under daylight rather than under a lamp

Age-related finish shift disclosed up front, as a new white panel next to a fifteen year old one rarely reads the same

Hinges checked for wear, pulled fixings and the sag that shows up first at the latch edge

Panel drop measured against the frame to see whether the panel has settled or the opening has

Louver tension tested one louver at a time instead of judged by feel across a whole panel

Broken louver pins, staples and tilt linkage diagnosed separately, since they fail for different reasons

Hidden rod linkage inspected inside the stile where the tilt has gone loose on a modern panel

Center tilt rod staples and clips checked on traditional panels where the rod has separated from a louver

Magnets, catch plates and strike points replaced where panels no longer hold closed

Frame plumb rechecked with a level, because a house that has settled will hold a good panel out of square

Shims and fixings reset where the frame itself has moved rather than the panel

Touch-up and refinishing limits explained honestly, as a factory finish can be blended and not truly restored

We offer repairs only on treatments The Window Valet installed or has serviced before. If we haven't worked on your treatments, we'll book a consultation for new ones. Wet-room damage assessed for what it is, since a hardwood panel that has taken years of shower humidity may be past repair

Work quoted per project after inspection, never against an invented range for a category nobody publishes

Every panel closed, latched and tilted through full travel before the visit ends

Hinge replacement and reset: Worn hinge knuckles, stripped fixings and pulled screws in a stile. This is the most common shutter failure by a distance, and it usually shows as a panel dropping at the latch edge and catching on its neighbor. A hinge set and fresh fixings often fix an entire opening.

Louver tension service: The friction that holds a louver where you leave it comes from tension pins or a tension screw in the stile. Louvers that fall open on their own or need two hands to move are tension problems, and most panels have an adjustment before anything gets replaced.

We offer repairs only on treatments The Window Valet installed or has serviced before. If we haven't worked on your treatments, we'll book a consultation for new ones. Broken louver replacement: A single cracked or snapped louver swapped out of the panel. This is where matching gets decided. Louver profiles are proprietary and sizes vary by manufacturer, so a louver from a line that has been discontinued is often the thing that ends a repair.

We offer repairs only on treatments The Window Valet installed or has serviced before. If we haven't worked on your treatments, we'll book a consultation for new ones. Center tilt rod repair: On a traditional panel the rod is stapled or clipped to each louver, and staples pull out. Reseating them properly means working into the louver edge without splitting it, and on an old painted panel that takes patience and a touch-up afterward.

We offer repairs only on treatments The Window Valet installed or has serviced before. If we haven't worked on your treatments, we'll book a consultation for new ones. Hidden rod linkage repair: On a clean-face panel the linkage lives inside the back of the stile, and when it loosens the louvers go out of step with each other. Getting to it means opening the stile, which is real work and part of the honest tradeoff for the look.

Magnet and catch replacement: Panels are held closed by small magnets set into the frame with steel catch plates on the panel. Magnets weaken and plates work loose. It's a small part and a fast fix, and it's the reason a lot of shutters stop sitting flat against their frame.

We offer repairs only on treatments The Window Valet installed or has serviced before. If we haven't worked on your treatments, we'll book a consultation for new ones. Frame reset and shimming: Where the opening has moved rather than the shutter, the fix is at the frame. Pulling the fixings, re-shimming to plumb and refastening puts the panels back into a square hole. It's the right repair on an older house that has settled since the shutters went in.

We offer repairs only on treatments The Window Valet installed or has serviced before. If we haven't worked on your treatments, we'll book a consultation for new ones. Panel replacement: A single panel remade to the existing frame where the old one is beyond repair. It depends entirely on whether the manufacturer still makes that louver size, frame profile and finish. When they don't, the honest options are a full elevation or living with the damage.

Touch-up and finish blending: Chips, dings and hinge scars addressed with a matched touch-up. Be realistic about what this achieves: a good blend disappears at three feet and is visible at one. Refinishing a factory-finished panel properly is a repaint, not a touch-up.

We offer repairs only on treatments The Window Valet installed or has serviced before. If we haven't worked on your treatments, we'll book a consultation for new ones. Wet-room reassessment: Where hardwood panels have spent years in a bathroom, the damage is often in the joints rather than on the surface. We'll tell you when the repair is a composite replacement for that room instead, since fixing the panel doesn't fix the reason it failed.